It is high-polymer modified cement elastic waterproofing coating (JS) is made up by acrylate emulsion, cement and inorganic materials to be form elastic waterproof film to protect building structurer.
Product Features
It has environment friendly, non-toxic, harmless and safe performance.
High bonding strength, it can be bonded firmly with many types of mortar substrate.
Can be applied on wet and dry substrate directly
Good performance of flexibility, waterproof and durability
Can be applied on vertical, slope and top surface directly, no flow, easy to use
Good weatherability, it can be applied on the outdoor roof without special protective layer (normal protective layer is needed)
Where to use
It is suitable for building wall, bathroom, kitchen ,balcony roof and so on.
How to use
Substrate preparation
The substrate must be smooth, firm, clean, without obvious water trace, fix the crack, the internal and external corner should be made into round corner.
Clean the old concrete surface with strong detergent, and then further clean with water, wait until it is completely dry before application.
Add the powder into liquid slowly and use mechanical mixer (350-450 rotations per min) to stir them evenly in 3-5min.
Operation points
Multi-layer applied by roller and scraper. The coatings should not too thick or it will dry too long.
Apply the protective layer after the coating is dry (5-7days normal temperature condition).
Announcements
Constructing below 5℃ or in the sand are not allow.
If it is wet or ventilation is poor, the coating will dry slowly, otherwise it will dry quickly.
Technical database
GB/T 23445-2009
| No. | experimental project | technical target |
| Type Ⅰ | TypeⅡ |
| 1 | solid content, % | 70 | |
| 2 | tensile strength, MPa ≥ | 1.2 | 1.8 |
| 3 | elongation at break,% ≥ | 200 | 80 |
| 4 | low temperature flexibility 10mm ≥ | -10 flawless | —— |
| 5 | 0.3MPa, 30 min | watertight | Watertight1) |
| 6 | impermeability, MPa ≥ | 0.5 | 0.7 |
| 7 | impermeability (Mortar dorsal surface)2) MPa ≥ | —— | 0.6 |
| 1 | solid content, % | 70 | |
| 2 | tensile strength, MPa ≥ | 1.2 | 1.8 |
| 3 | elongation at break,% ≥ | 200 | 80 |
| 4 | low temperature flexibility 10mm ≥ | -10 flawless | —— |
| 5 | 0.3MPa, 30 min | watertight | Watertight1) |
| 6 | impermeability, MPa ≥ | 0.5 | 0.7 |
| 7 | impermeability (Mortar dorsal surface)2) MPa ≥ | —— | 0.6 |
Packing Size
18kg/ pail
Consumption
Type Ⅰ: 1.8-2 kg/m2
Flood test
Prior to placement of protection, flood to a minimum depth of 50mm of water for 24 hours. Drains shall be plugged and barriers placed to contain the water.
Storage/Shelf life
12 months if kept below 25℃ in the original unopened pack.
Curing and protection
Waterproof membrane must be cured for a minimum of 24 hours @25℃ before placing protection. Where damage(by traffic, back filling, etc) to the membrane is possible, it should be protected by a cementitious screed or protection boards. Where a bond with topping is not required, a separator sheet should be used.
Cleaning
Tools and equipment should be cleaned with water immediately after application.
Precautions
Health and safety
Some people are sensitive to this product. Wear gloves and skin barrier cream when handling these products.
Use of goggles is recommended. In case of accidental eye contact, wash thoroughly with plenty of clean water and seek medical advise immediately.
Ensure adequate ventilation when using resin and solvent containing materials.