Wall decor plasters Cement texture render concrete polished vintage grey wall finish

Maydos wall decor plasters Concrete Effect is an interior/exterior water based paint that creates the textural effect of polished concrete. Apply Concrete effect with a roller and finish off with a steel trowel to achieve the concrete appearance.

Add to quote

Categories: Architectural Paint, Decorative paint

Maydos concrete look polished plaster wall finishing plasters

Product type: Decorative paint / water based paint

MOQ:500kg ( We offer free sample!!! )

Concrete Finish Plaster

The product is applied by	Brush ; Roller ; Trowel
Cleaning of painting tools	Water
Theoretical coverage	1.0 – 1.7 kg/m2 in two coats, depending on the kind of substrate.
Dilution	No recommended.
Surface Preparation	For previously painted surfaces that are in good condition, dust, then clean with soap.
	For surfaces with cracks or holes, repair with appropriate filler.
	Spot prime repairs with Maydos Primer Sealer Undercoat.
	For glossy surfaces lightly sand to a dull finish.
	For Plasterboard, Brick, Cement and bare timber apply 1 coat of Maydos Primer Sealer Undercoat.
	For Set Plaster, Fibrous Plaster, or Plasterglass, apply 1 coat of Maydos Sealer Binder.
Application Procedure And Equipment	To ensure evenness of color, pour all cans of Maydos Concrete Effect into a clean dry container. Stir thoroughly prior to use. Before you begin, test your chosen application method on a large piece of board.
	Work in small sections. Use a long nap roller to apply Concrete Effect to the wall.
	Smooth the surface with a steel trowel with broad, sweeping strokes, holding the trowel at a 60° to 80° angle. Be sure to keep the edge of trowel clean, by wiping any build up on the trowel edge with a wet cloth. Repeat this process over the entire wall.
	Apply 2-3 coats using the same process. Applying additional coats will enhance the depth and appearance of the finish. The final coat should dry for at least 2 hours, but no longer than 24 hours, before polishing.
	Using 600-grit sandpaper, lightly polish the surface in a circular motion. Use the edge of the trowel to further polish the surface. Apply enough pressure to keep the trowel edge flat against the surface. Be careful not to gouge the surface with the edge of the trowel.
	For further protection, allow Concrete Effect to dry overnight and seal with one coat of Maydos wall varnish as overcoat.
Recommended paint system
Primer	Maydos anti-alkali primer M-003 : 1 coat
Top Coat	Maydos concrete effect paint : 2-3 coats
Over Coat (optional)	Maydos wall varnish : 1 coat

Click to enlarge

Previous product

Road Marking Paint Fast Drying Thermoplastic Traffic Paint

Next product

Polyester Wood Varnish Maydos Environment friendly Solvent base

Compare

Description
Technical Data
Compare to others
Application
Project case
Package

Description

Technical Data

polished concrete wall coating

Color	Cement color
Type	Water-based
Thinner	Not recommended
Mixing Ratio	N/A
Gloss Level	Matt paint effect
V.O.C. Level	4.5g/L tinted

Compare to others

wall paint

Application

The product is applied by	Brush ; Roller ; Trowel
Cleaning of painting tools	Water
Theoretical coverage	1.0 – 1.7 kg/m2 in two coats, depending on the kind of substrate.
Dilution	No recommended.
Surface Preparation	For previously painted surfaces that are in good condition, dust, then clean with soap.
	For surfaces with cracks or holes, repair with appropriate filler.
	Spot prime repairs with Maydos Primer Sealer Undercoat.
	For glossy surfaces lightly sand to a dull finish.
	For Plasterboard, Brick, Cement and bare timber apply 1 coat of Maydos Primer Sealer Undercoat.
	For Set Plaster, Fibrous Plaster, or Plasterglass, apply 1 coat of Maydos Sealer Binder.
Application Procedure And Equipment	To ensure evenness of color, pour all cans of Maydos Concrete Effect into a clean dry container. Stir thoroughly prior to use. Before you begin, test your chosen application method on a large piece of board.
	Work in small sections. Use a long nap roller to apply Concrete Effect to the wall.
	Smooth the surface with a steel trowel with broad, sweeping strokes, holding the trowel at a 60° to 80° angle. Be sure to keep the edge of trowel clean, by wiping any build up on the trowel edge with a wet cloth. Repeat this process over the entire wall.
	Apply 2-3 coats using the same process. Applying additional coats will enhance the depth and appearance of the finish. The final coat should dry for at least 2 hours, but no longer than 24 hours, before polishing.
	Using 600-grit sandpaper, lightly polish the surface in a circular motion. Use the edge of the trowel to further polish the surface. Apply enough pressure to keep the trowel edge flat against the surface. Be careful not to gouge the surface with the edge of the trowel.
	For further protection, allow Concrete Effect to dry overnight and seal with one coat of Maydos wall varnish as overcoat.
Recommended paint system
Primer	Maydos anti-alkali primer M-003 : 1 coat
Top Coat	Maydos concrete effect paint : 2-3 coats
Over Coat (optional)	Maydos wall varnish : 1 coat